IDX BH-2 (BH2) ENDURA ELITE Battery Housing Only. PLEASE NOTE: This item is the Housing Only - Cartridges are NOT included.
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig. Direct Drive Motor ...
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig. Direct Drive Motor ...
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig.
This is a custom cable that runs from the Spectrum ST4's i/o port to the Nodo Inertia Wheels Receiver (RX).
Movement: ST4 - 4 axis motion controller - Pan/Tilt/Focus and Slide on Dana Dolly
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
Movement: ST4 - 4 axis motion controller - Pan/Tilt/Focus and Slide on Dana Dolly
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
The xR3ACH Waterproof cover, is our thinnest and softest cover for the xR3ACH back mount. Its inner fleece material keeps the back mount protected from anything that might rub or scratch against it.
The Winter softshell cover is a neoprene cover that keeps your xR3ACH performing at its best at sub-zero temperature (0C/32F down to -20C/-4F).
The Serene Bungee grip is a small hook that holds the bungee cord in place.
It’s placed on ONE side of the Serene arm, where the bungee cord is attached. This holds it in place, so you never lose your bungee cord ever again!
It’s placed on ONE side of the Serene arm, where the bungee cord is attached. This holds it in place, so you never lose your bungee cord ever again!
52 to 64 lb Load Capacity Range, Change Core for Different Weight Setup, Pre-Extended for Quick Change ...
37 to 49.5 lb Load Capacity Range, Change Core for Different Weight Setup, Pre-Extended for Quick Change ...
31 to 43 lb / 14 bis 19.5 Kg Load Capacity Range, Change Core for Different Weight Setup.
Pre-Extended for Quick Change ...
Pre-Extended for Quick Change ...
17.5 to 31 lb Load Capacity Range - Change Core for Different Weight Setup - Pre-Extended for Quick Change ...
The GLINK 1.5 offers significant upgrades in performance over the previous GLINK V1.0. The following features and upgrades has been done:
New retraction bracket geometry and ensures better folding behavior for the operator.
New retraction bracket geometry and ensures better folding behavior for the operator.
For Black Arm 3-Axis Stabilizer, Replacement Tilt Arm Dampener, Use for Extra Dampening
The Black Arm Tilt Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer ...
The Black Arm Tilt Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer ...
The FLOWCINE Black Arm Roll Dampener replaces the existing roll dampener of your FLOWCINE Black Arm stabilizer system.
The Universal Rack clamps on to the tow bar of your car. It allows two Pro Clamp singles to be attached for further mounting of standard 48-51mm tubes. The Universal Rack is very easy to attach, and mounts on to any standard 50mm tow bar.
The Flowcine Stub mount is a small lightweight 50mm tube that you can attach through a car’s tow eye bolt or similar.
The GLINK Case is a dual layered, custom foamed Peli AIR 1637 travel case, equipped with wheels and retractable handle bar for lightweight and trouble free packing of the GLINK system.
The GLINK Docking Station allows the operator to easily store all necessary GLINK parts in one place while working on set.
The GLINK docking station tool rack is a clean way to store your tools on the docking station.
GLINK Spring Cores ( 18.0 - 24.9 KG, blau ) - g-Spring-Blue *
2 x Spring Cores, 22-34 lb, Black, Integral Component of GLINK Stabilizer ...
