Protects your Stabil and Stabil G2 arm from dirt and scratches.
The kit allows you to configure your rig in super high mode, high mode and low mode. It also includes the Low mode grip handle, which allows for more comfortable hand placement for the operators control hand, when working in low mode.
Battery Capacity: 14.4V, 4.6Ah (9.6Ah as one pair), 68Wh*
End Voltage: 12V
End Voltage: 12V
This is a custom cable that runs from the Spectrum ST4's i/o port to the Nodo Inertia Wheels Receiver (RX).
The Serene Bungee grip is a small hook that holds the bungee cord in place.
It’s placed on ONE side of the Serene arm, where the bungee cord is attached. This holds it in place, so you never lose your bungee cord ever again!
It’s placed on ONE side of the Serene arm, where the bungee cord is attached. This holds it in place, so you never lose your bungee cord ever again!
17.5 to 31 lb Load Capacity Range - Change Core for Different Weight Setup - Pre-Extended for Quick Change ...
The Flowcine Stub mount is a small lightweight 50mm tube that you can attach through a car’s tow eye bolt or similar.
The GLINK Case is a dual layered, custom foamed Peli AIR 1637 travel case, equipped with wheels and retractable handle bar for lightweight and trouble free packing of the GLINK system.
The GLINK Docking Station allows the operator to easily store all necessary GLINK parts in one place while working on set.
CF RING FOOT 3 feet - g-Foot-3
Feet for your CF Ring, to be able to put down your rig without a docking stand.
Feet for your CF Ring, to be able to put down your rig without a docking stand.
Holds GLINK Upright without Stand, 1/4"-20 and 3/8"-16 Female Threads, Clamps to Bottom CF Ring, Designed for GLINK Stabilization System ...
The Monitor clamp for CF Ring is a quick way to attach a monitor to your gimbal setup.
The GLINK handheld mount is a telescopic mount for either hard mounted cameras and/or electronic heads such as the ARRI Trinity, MK-V Omega/AR or the Betz Wave.
The xARM is based on polymer spring cores with a outer shell of Neoprene. Each spring core has a smooth and linear lifting capacity and when being used near their maximum ...
The xDrop is a male to female socket block connection bracket that drops the arm connection 85mm / 3.4″.
The xDROP, is a new male socket block-to-female socket block connection bracket, that drops the arm connection to the vest approx 85mm or 3.4″ and offsets the same connection to the side 55mm or 2.2″.
The xPEG Rip-Tie also comes with a ⅜”-16 UNC threaded hole, if the user wishes to mount anything else on it (such as a eyebolt, for example).
100mm Front extension block. For the larger frame gimbals, you may need to extend the Black a little bit.
Tranquilizer O-ring pack shore 20
Black Arm Tranquilizer Shore Pack 20 (12-23 lb)
Black Arm Tranquilizer Shore Pack 20 (12-23 lb)
Black Arm Tranquilizer Shore Pack 50 (30-60 lb)
Tranquilizer O-ring pack shore 50
Tranquilizer O-ring pack shore 50
The Pan Barrels are the links that run around the Tranquilizer, dampening the pan axis. Gimbals/remote heads with stronger pan motors needs stiffer Pan Barrels ...
The Black Mitchell Nut is a Mitchell castle nut that is more narrow than most castle nuts, making it fit through the rods of our Female Mitchell mount.
Dana Dolly Monitor Mount for Dana Dolly (p/n DDMM1). Adjustable monitor mount for small monitors 5lbs and under. Threaded 3/8" stud goes into available hole in Dana Dolly and secures with a wingnut.
150mm adapter for large camera heads that use a 150mm ball base for leveling. This is a quality, made in USA product that will also fit other standard Mitchell Mounts.
