Dana Dolly and additional equipment

Sort by:

Portable Dolly System Rental Kit with Universal Track Ends ...
€1.290,00 (€1.375,00 / ) *
* Excl. tax Excl. Shipping costs
Dana Dolly 6" Riser. Adds 6" Camera Height for shots that require the camera to be a little higher on the track.
€135,00 (€165,00 / ) *
* Excl. tax Excl. Shipping costs
Dana Dolly adapter that fits the Sachtler Aktiv 6, 8, and 8T quick release fluid heads. 75mm bowl. Works with any Dana Dolly made after 1985. Will not work with other dollies. Made in USA of USA materials.
€150,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly Universal Rental Kit - Dolly + 75/100/150mm adapter + case
€1.350,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly Leveling Leg. Easy to use Leveling from ground to 12".
€175,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly "Perm" 75mm ball adapter. For use with all Dana Dolly systems.
€175,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly adapter that fits the Sachtler 100mm Aktiv 10 fluid head.
€139,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly 100mm Ball Camera Head Adapter (p/n DDBRK3). Dana Dolly 100mm Ball Adapter
€135,00 *
* Excl. tax Excl. Shipping costs
9' of Portable Triangular Dolly Track, Supports 100 Pounds ...
€1.470,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly "Perm" 100mm ball adapter. For use with all Dana Dolly systems. Allows the adapter to be mounted to the Dana Dolly ...
€165,00 *
* Excl. tax Excl. Shipping costs
150mm adapter for large camera heads that use a 150mm ball base for leveling. This is a quality, made in USA product that will also fit other standard Mitchell Mounts.
€149,00 *
* Excl. tax Excl. Shipping costs
Portable Dolly System w/ Universal Track Ends - 75mm & 100mm Bowl Adapters
€975,00 *
* Excl. tax Excl. Shipping costs
The Dana Dolly Portable Camera Slider is the same dolly found in all of the Original (Non-Hi Hat) kits ...
€695,00 *
* Excl. tax Excl. Shipping costs
The Dana Dolly Brake. For use when the dolly is being used as a still platform. Made in USA of Aluminum and Stainless.
€145,00 *
* Excl. tax Excl. Shipping costs
Highlights: Designed to hold 1 1/4" pipe or conduit, Anodized aluminum ...
€145,00 *
* Excl. tax Excl. Shipping costs
Highlights: Dana Dolly Hi Hat Slider, 2-Universal Track Ends, 75mm,100mm,150mm Ball Adapter, Monitor Mount ...
€2.240,00 *
* Excl. tax Excl. Shipping costs
Portable Dolly System w/ Universal Track Ends - 100 & 150mm Bowl Adapters
€998,00 *
* Excl. tax Excl. Shipping costs
Custom SKB Flight Case with Custom Foam. Wheeled with Fold Down Handle. Fits Dana Dolly, 2-Track Ends, 75mm, 100mm, 150mm Adapters ...
€390,00 (€475,00 / ) *
* Excl. tax Excl. Shipping costs
Removable Mitchell Plate Hi Hat, Mitchell Plate to 100mm Bowl Adapter, Anti-Tip Brackets, Soft Polyurethane Track Wheels ...
€1.275,00 *
* Excl. tax Excl. Shipping costs
Allows the adapter to be mounted to the Dana Dolly, May not work with Non-Dana Dolly sliders. Important to check 65mm and not 75mm ball.
€125,00 *
* Excl. tax Excl. Shipping costs
This is just the Dana Dolly. Made in the USA. T-6061 Aluminum, Black.
Item: DanaDolly
€775,00 *
* Excl. tax Excl. Shipping costs
Removable Mitchell Plate Hi Hat, Mitchell Plate to 100mm Bowl Adapter, Anti-Tip Brackets, Soft Polyurethane Track Wheels ...
€1.290,00 *
* Excl. tax Excl. Shipping costs
Dana Dolly Monitor Mount for Dana Dolly (p/n DDMM1). Adjustable monitor mount for small monitors 5lbs and under. Threaded 3/8" stud goes into available hole in Dana Dolly and secures with a wingnut.
€78,00 *
* Excl. tax Excl. Shipping costs
150mm adapter for large camera heads that use a 150mm ball base for leveling. This is a quality, made in USA product that will also fit other standard Mitchell Mounts. 
€145,00 *
* Excl. tax Excl. Shipping costs
* Excl. tax Excl. Shipping costs

About

The Dana Dolly is an updated version of a design used in the film industry for decades.  After making similar dollies for years for friends, Mike Hall decided to simplify the design, and modify the components and composition to make the entire system easier to use and more affordable.

The dolly is the product of hundreds of shoots and modifications since the early 1980s, when the cameras were much heavier.  We tried a number of different wheels and bearings, and composites, steel, and aluminum before coming up with the combination that we believe is all three: Good, Fast, and Cheap.

The Dana Dolly V2.0 is now made of 6061 Aluminum finished Black to cut down on reflectivity. The bottom of the plate is milled out to cut down on overall weight, while not compromising strength. The triangle trucks are a custom extruded aluminum profile that is patent pending, finished black. The wheels are custom made soft, then turned down to be round within 1/1000 of an inch (thinner than a human hair) to eliminate the "bounce" that normal skateboard wheels give. 

The turning process also helps keep down the squeak that some dollies experience.  We have our bearings specially made to compliment the wheels. The dolly wheels are designed soft to give a very smooth, squeak free move with any size camera, and can be used for today's SLR's and full-sized 35mm cameras with no problem. Heavier cameras may require the use of a middle support for longer track moves, and the wheels are not a good fit for any use that would put over 100lbs on 16 wheels.

The dolly now has a 1/4-20 and 3/8-16 threaded hole on each side for accessories such as LED lights or monitors, as well as a 3/8" through - hole in the middle of each side. The plate measures approximately 14" long and 10" wide, and the trucks are just shy of 12" on center.  The plate has a standard Mitchell Mount milled into the center of the dolly plate, with an elongated slot to accompany non-standard adapters.  We make three standard sizes of ball-mount adapters: 75mm, 100mm, and 150mm.

The Track Ends are designed to go into any "Junior" or 1 1/8" receiver. They do work with "Baby" stands, or "C" stand spuds, however we highly recommend using Junior Stands. After a couple of years of making track ends that fit these stands, we determined that baby stands are just too unstable to handle the dolly setup. Most customers use a "Baby Combo" stand to support the track.

The original dollies were made of Wood, then Aluminum, and then we had a composite Dana Dolly. The composite proved too expensive for our purpose, so once again since 2010 the dolly is made from Aluminum.

Designed and manufactured in the USA.

 

The Dana Dolly is an updated version of a design used in the film industry for decades.  After making similar dollies for years for friends, Mike Hall decided to simplify the design, and modify the components and composition to make the entire system easier to use and more affordable.

The dolly is the product of hundreds of shoots and modifications since the early 1980s, when the cameras were much heavier.  We tried a number of different wheels and bearings, and composites, steel, and aluminum before coming up with the combination that we believe is all three: Good, Fast, and Cheap.

The Dana Dolly V2.0 is now made of 6061 Aluminum finished Black to cut down on reflectivity. The bottom of the plate is milled out to cut down on overall weight, while not compromising strength. The triangle trucks are a custom extruded aluminum profile that is patent pending, finished black. The wheels are custom made soft, then turned down to be round within 1/1000 of an inch (thinner than a human hair) to eliminate the "bounce" that normal skateboard wheels give. 

The turning process also helps keep down the squeak that some dollies experience.  We have our bearings specially made to compliment the wheels. The dolly wheels are designed soft to give a very smooth, squeak free move with any size camera, and can be used for today's SLR's and full-sized 35mm cameras with no problem. Heavier cameras may require the use of a middle support for longer track moves, and the wheels are not a good fit for any use that would put over 100lbs on 16 wheels.
 
The dolly now has a 1/4-20 and 3/8-16 threaded hole on each side for accessories such as LED lights or monitors, as well as a 3/8" through - hole in the middle of each side. The plate measures approximately 14" long and 10" wide, and the trucks are just shy of 12" on center.  The plate has a standard Mitchell Mount milled into the center of the dolly plate, with an elongated slot to accompany non-standard adapters.  We make three standard sizes of ball-mount adapters: 75mm, 100mm, and 150mm.

The Track Ends are designed to go into any "Junior" or 1 1/8" receiver. They do work with "Baby" stands, or "C" stand spuds, however we highly recommend using Junior Stands. After a couple of years of making track ends that fit these stands, we determined that baby stands are just too unstable to handle the dolly setup. Most customers use a "Baby Combo" stand to support the track.

The original dollies were made of Wood, then Aluminum, and then we had a composite Dana Dolly. The composite proved too expensive for our purpose, so once again since 2010 the dolly is made from Aluminum.
 
Designed and manufactured in the USA.
Please accept cookies to help us improve this website Is this OK? Yes No More on cookies »
You are using a really old version of
Internet Explorer, click here to upgrade your browser.
x