The Super-high/low mode link bracket, joins two arm posts with a lockable link, allowing the long and regular arm posts to be used both in high mode and low mode.
CL-CB1, Olympus connector supports: Olympus: E1,E3,E10,E20,E30.
CL-S1, Sony connector supports:
Sony a900, Sony a700, Sony a350, Sony a300, Sony a200, Sony a100, Sony a100K, a100,a77,a65,a57,a55,a37,a35,a33, a99
Sony a900, Sony a700, Sony a350, Sony a300, Sony a200, Sony a100, Sony a100K, a100,a77,a65,a57,a55,a37,a35,a33, a99
Nikon CL-DC2 connector supports:
D7500, D7200, D7100, D7000, D5600, D5500, D5300, D5200, D5100, D5000, D3100, D600, D610, D90, Z6, Z7
D7500, D7200, D7100, D7000, D5600, D5500, D5300, D5200, D5100, D5000, D3100, D600, D610, D90, Z6, Z7
Nikon CL-DC1 connector supports: Nikon D70, D80
Nikon CL-DC0 (10-Pin) connector supports:
Nikon D1H, D1X, D2H, D2X, D2Xs, D2Hs, D200, D3, D4, D4s, D300, D700, D800, D810, D850, F90x, F90, F100, F6, F5 Kodak DCS-14n Fujifilm S3 Pro, S5 Pro
Nikon D1H, D1X, D2H, D2X, D2Xs, D2Hs, D200, D3, D4, D4s, D300, D700, D800, D810, D850, F90x, F90, F100, F6, F5 Kodak DCS-14n Fujifilm S3 Pro, S5 Pro
Alpha a9, a7, a7 II, a7 III, a7R, a7R II, a7R III, a7S, a7S II, a6500, a6400, a6300, a6000, a5100, a5000, a3000, a77 II, a58
Cyber-shot RX1R II, RX10 IV, RX10 III, RX10 II, RX10, RX100 VI, RX100 VA, RX100 V, RX100 IV, RX100 III, RX100 II ...
Cyber-shot RX1R II, RX10 IV, RX10 III, RX10 II, RX10, RX100 VI, RX100 VA, RX100 V, RX100 IV, RX100 III, RX100 II ...
1DX Mark II, 1D X, 1D C, 1Ds Mark III, 1Ds Mark II, 1Ds, 1D Mark IV, 1D Mark III, 1D Mark II N, 1D Mark II, 1D, 5DS R, 5DS, 5D Mark IV, 5D Mark III, 5D Mark II, 5D, 50D, 40D, 30D, 20D, 10D, 6D Mark II, 6D, 7D Mark II, 7D
The Black T-nut is a clever M12x1.75 nut for tool less or 19mm wrench tightening.
The kit allows you to configure your rig in super high mode, high mode and low mode. It also includes the Low mode grip handle, which allows for more comfortable hand placement for the operators control hand, when working in low mode.
The kit allows you to configure your rig in super high mode, high mode and low mode. It also includes the Low mode grip handle, which allows for more comfortable hand placement for the operators control hand, when working in low mode.
The kit allows you to configure your rig in super high mode, high mode and low mode. It also includes the Low mode grip handle, which allows for more comfortable hand placement for the operators control hand, when working in low mode.
The Winter softshell cover is a neoprene cover that keeps your xR3ACH performing at its best at sub-zero temperature (0C/32F down to -20C/-4F).
44.5 to 56 lb Load Capacity Range, Change Core for Different Weight Setup, Pre-Extended for Quick Change ...
31 to 43 lb / 14 bis 19.5 Kg Load Capacity Range, Change Core for Different Weight Setup.
Pre-Extended for Quick Change ...
Pre-Extended for Quick Change ...
The xARM is a double section articulated stabilization arm, made from aircraft grade aluminium, solid carbon fibre infused titanium shafts and large stainless steel precision ball bearings
The FLOWCINE Black Arm Roll Dampener replaces the existing roll dampener of your FLOWCINE Black Arm stabilizer system.
The xDrop is a male to female socket block connection bracket that drops the arm connection 85mm / 3.4″.
The xDROP, is a new male socket block-to-female socket block connection bracket, that drops the arm connection to the vest approx 85mm or 3.4″ and offsets the same connection to the side 55mm or 2.2″.
The xPEG Rip-Tie also comes with a ⅜”-16 UNC threaded hole, if the user wishes to mount anything else on it (such as a eyebolt, for example).
The xPEG is a hook that you mount on your cart, where you can hang your Steadicam arm.
The xPEG Rip-Tie allows the operator to tighten up the arm at the bottom shelf of the cart.
The xPEG Rip-Tie allows the operator to tighten up the arm at the bottom shelf of the cart.
Replacement camera mounting pin for camera mounting plate assembly (601-7412 and 802-7417). The pin screw is compatible with Clipper 2, Clipper, Vector and Archer_2S.
Compatible withClipper 2, Clipper, Vector, Archer_2S
Compatible withClipper 2, Clipper, Vector, Archer_2S
The Rigid nose mount is an accessory for the times where you need to lock up the roll/tilt movement for the Black arms head. Common use cases could be when the Black is mounted on to a motorcycle ...
100mm Front extension block. For the larger frame gimbals, you may need to extend the Black a little bit.
